Alignment is the one job we do not offer from the vans. Accurate measurement needs a level floor, calibrated equipment and the car settled on its suspension, which a basement or driveway cannot provide. Most alignments take 45–60 minutes, and you can wait in the workshop or leave the car with us.
If your tyres are already worn on one edge, alignment will not save them, but it will save the next set. We usually suggest pairing it with EV tyre replacement so new tyres start life on a straight car.
What's different on an EV
EVs punish small alignment errors more than petrol cars do. The battery adds several hundred kilograms low in the chassis, and that weight presses the suspension into its geometry harder, so a fraction of a degree of excess toe or negative camber scrubs tread with every kilometre. The Tesla Model Y is the clearest example we see: its rear wheels run noticeable negative camber from the factory, and with toe slightly out of range, the inner shoulders of the rear tyres wear through while the centre still looks healthy.
Regenerative braking adds another load. Every time you lift off the accelerator, the motors slow the car through the tyres, pulling the wheels against their alignment in a way a petrol car only does under braking. Combine that with instant torque on take-off and a geometry error is exercised in both directions all day long. That is why we align EVs to the tight end of the maker's tolerance, not just anywhere inside the green band.
When you need wheel alignment
- The car drifts left or right on a straight, flat road
- The steering wheel is off-centre when driving straight
- Tyres wearing on the inner or outer edge faster than the centre
- You hit a pothole, kerb or speed bump hard
- New tyres, suspension parts or lowering springs were just fitted
- A feathered feel when you run your hand across the tread
How we do it
- 01
Check pressure and ride height
We set tyres to placard pressure and, on air suspension cars, confirm the car sits at its normal ride height before measuring.
- 02
Mount targets and measure
Targets go on all four wheels and the rig reads camber, caster and toe on each corner, plus thrust angle.
- 03
Adjust what the car allows
We adjust toe front and rear and camber where the design permits, to the tight end of the maker's range.
- 04
Centre the steering
The steering wheel is centred, and on cars that need it, the steering angle sensor is reset so lane-keeping reads straight.
- 05
Print and road test
You get a before-and-after printout and we road test the car to confirm it tracks straight.
Why the Model Y wears the inside edge of its tyres
It is mostly geometry. The Model Y's rear wheels run negative camber, leaning in at the top, and the inner shoulder carries more load as a result. If rear toe drifts out of range, the inner shoulder also scrubs, and the combination wears it far faster than the rest of the tread.
Owners often notice only when the tyre goes soft or a technician spots the cords. From the outside the tread looks fine, so the problem hides until it is serious. Our post on Tesla Model Y uneven tyre wear shows typical examples.
Rear toe is adjustable on the Model Y and correcting it to the tight end of spec helps a lot. Camber is limited from the factory, so if a car still eats inner shoulders after a good alignment, aftermarket adjustable rear links are an option, and we explain the cost and trade-offs before you decide.
What knocks alignment out on UAE roads
Speed bumps and kerbs, more than potholes. Main roads in Dubai and Abu Dhabi are generally smooth, but residential communities are full of tall speed bumps, and villa driveways often have sharp kerb edges. Taking a bump at an angle, or dropping a wheel off a high kerb in a mall car park, can shift toe on a heavy EV.
Low-profile tyres make it worse, because a 35-series sidewall on a 21-inch wheel gives the suspension less cushion. We also see alignment change after construction-zone diversions, where temporary road edges are rough.
As a guide, have alignment checked once a year, after any hard impact, and whenever you fit new tyres. It is cheaper than a pair of 21-inch tyres.
Alignment and driver assistance: what we adjust and what we leave
We set wheel geometry and centre the steering. On most EVs that is all that is needed, and the driver-assistance cameras read the road correctly afterwards.
Some cars need their camera or radar recalibrated after alignment or windscreen work. Teslas usually recalibrate their cameras themselves over a few drives, and the car tells you when it is done. Other makes, particularly some German and Korean models, may need dealer-level tools for full ADAS recalibration. We tell you before we start if your car is one of those, so you can book it in with the dealer afterwards.
If lane-keeping pulls to one side after an alignment elsewhere, the steering angle sensor may not have been reset. We can check and reset it on most makes.
How to read the alignment printout
The printout has three main figures for each wheel. Toe shows whether the wheels point in or out when viewed from above; it causes the most tyre wear when wrong. Camber shows whether the wheels lean in or out at the top; too much negative camber wears the inner edge. Caster shows the angle of the steering axis; it affects straight-line stability and steering feel.
Each figure has a target and a green range. Readings in red are outside tolerance. We aim for the centre or the tight end of the range on EVs, and the after column should show all adjustable figures in green. If a figure cannot be brought into spec, such as camber on a car without adjusters, we mark it and explain why.
