Tesla Model Y Uneven Tyre Wear: Causes and How to Stop It
Model Y tyres often wear on the inner edge, especially at the rear. A UAE technician explains the camber, toe and rotation causes and how to stop it early.
· 6 min read

Tesla Model Y tyres most often wear unevenly on the inner edge, and usually at the rear. The wheels are set with negative camber, tilted in at the top, so the inner shoulder carries more of the car’s 2,000 kg on every corner. Add rear-biased torque, toe slightly off and no rotation, and the inner edge can reach the cords while the outer half of the tread still looks almost new.
The worst part is that you cannot see it. Standing beside the car, the tyre looks fine. We find it when a customer calls about a vibration or a puncture, and the inner shoulder is already showing steel.
What we find on a typical Model Y
Out of the Model Ys we inspect, a large share show some inner edge wear by 20,000 km. A typical example from earlier this year: a 2023 Model Y Long Range on the standard 255/45 R19 tyres, 24,000 km, never rotated, driven daily between Arabian Ranches and Downtown.
| Position | Outer edge | Centre | Inner edge |
|---|---|---|---|
| Front left | 5.5 mm | 5.8 mm | 4.9 mm |
| Front right | 5.6 mm | 5.9 mm | 5.0 mm |
| Rear left | 4.8 mm | 4.2 mm | 1.4 mm |
| Rear right | 4.7 mm | 4.1 mm | 1.6 mm |
New tread on that tyre is roughly 8 mm. The fronts had plenty left. The rears were at the legal limit on the inner edge only. Alignment showed rear toe slightly out of specification on both sides. The owner had to buy two new rear tyres at 24,000 km, and the fronts went on for another 12,000 km after rotation.
The wear patterns and what each one means
I read a Model Y tyre by running my hand across the full width and using a depth gauge at three points. Each pattern points to a different cause.
Inner edge worn, rest of tread fine
This is the classic Model Y pattern. Causes, in order of how often I see them:
- Rear toe out of specification. Even a small error drags the tyre sideways, scrubbing the inner shoulder.
- Negative camber. It is part of the design, but it concentrates load on the inner edge.
- No rotation. The rears carry most of the torque on RWD and many AWD drives, and never move to the front where wear is gentler.
- Lowering springs or aftermarket wheels. Lowering a Model Y increases negative camber noticeably.
Both edges worn, centre fine
Under-inflation. Common when owners set pressure hot in summer. The placard says 42 psi cold for the standard wheels, and I explain how to set it correctly in my guide to EV tyre pressure in UAE summer.
Centre worn, edges fine
Over-inflation, usually from topping up to 45–48 psi cold. Less common on Teslas because the TPMS display makes owners aware of pressure.
Feathered or saw-tooth edges
Run your hand across the tread. If the blocks feel smooth one way and sharp the other, toe is out. This often follows a kerb hit or a deep pothole.
Cupping or scalloped patches
Uneven dips around the circumference. Usually worn suspension bushings or a wheel out of balance. Less common on newer cars, but we see it on high-mileage Model Ys used for ride-hailing.
Why the Model Y is more prone to it
The Model Y is not badly designed. It is a heavy, powerful car with suspension set up for stable handling, and that geometry has a cost in tyre wear. Three things work together:
- Weight. Around 2,000 kg for the Long Range, heavier than any petrol SUV of its size.
- Torque at the rear. Even AWD versions send a lot of drive to the rear motor. Every launch from the lights on Al Khail Road loads the rear tyres.
- Geometry. Negative camber improves cornering grip but loads the inner shoulder in a straight line, which is most UAE driving.
From the factory, the main adjustment available is toe. Correcting camber beyond the standard range usually needs aftermarket adjustable arms, which I only recommend for lowered cars.
There is more on how heavy EVs wear their tyres in general in why EV tyres wear faster.
How to check yours
You need about five minutes and a phone.
- Turn the steering fully to one side to expose the front tyre’s inner edge. Photograph it.
- For the rears, crouch behind the car and use the phone camera with the flash on to see the inner shoulder.
- Run your hand across the tread width. Shallower tread or a smooth band on the inner third is the warning sign.
- Check the tread wear indicators, small raised bars in the grooves. If the inner groove is level with the bar, the tyre is at 1.6 mm.
If you see steel wire or fabric, do not drive at highway speed. That tyre can fail.
Fixing it
The fix depends on how far it has gone.
Caught early, inner edge at 3 mm or more. Book an alignment and a rotation. Bringing toe back into specification and moving the worn rears to the front evens out the wear. Our wheel alignment starts from AED 150 and tyre rotation from AED 80.
Inner edge below 3 mm, outer still good. Replace the two worn tyres, align the car and rotate the new ones on schedule. Fit the new pair at the rear if the car is square-setup, because grip at the rear matters most for stability.
Inner edge at the cords. Replace immediately. Do not wait for the next service.
For replacements, the common 19-inch Model Y size is 255/45 R19 104 XL. You will find OE-spec options on our Tesla Model Y tyres page, including T0-marked tyres with foam.
Questions to ask at the alignment
Not every alignment is the same. A quick toe-only setting with the wrong equipment can leave you where you started. When a Model Y comes in for wear problems, this is what I check, and what I suggest you ask for wherever you go:
- A before-and-after printout. You should see camber and toe for all four wheels, both before and after adjustment, against Tesla’s specification.
- Rear toe, not just front. Many quick alignments only touch the front. On a Model Y the rear toe matters most for inner edge wear.
- Ride height check. If the car has been lowered or sits on aftermarket springs, the geometry changes and the specification has to be read with that in mind.
- Correct steering wheel centring. After adjustment, the wheel should sit straight on a level road.
- Wear pattern noted. The technician should record the tread depths so you can compare at the next visit.
A good alignment on a Model Y takes 45–60 minutes. If it is done in ten, ask what was adjusted.
Tyre choice helps too
Some tyres tolerate camber better than others. Tyres with a stiffer inner shoulder hold up better on the Model Y. In our experience the OE-spec T0 tyres generally wear more evenly on this car than budget tyres in the same size, because they were developed on it.
What about the Performance model
The Model Y Performance runs staggered 21-inch tyres, with wider tyres at the rear. You cannot rotate front to rear. That means the rears will always wear faster, and inner edge wear is common. On these cars I recommend:
- An alignment check every 10,000 km.
- Side-to-side swaps where the tyres are not directional, which shifts the wear pattern slightly.
- Budgeting for rear tyres roughly twice as often as fronts.
What I would do
Photograph your inner edges this weekend. If they look the same as the outer edges, set a rotation reminder for every 8,000–10,000 km and carry on.
If the inner edges are visibly worse, book an alignment before rotating. Rotating worn tyres onto a misaligned car just moves the problem around.
When the time comes for new tyres, align the car on the day they are fitted. It costs less than one tyre and it is the main reason some of our Model Y customers get 38,000 km from a set while others get 24,000 km.


