EV Wheel Alignment Explained: Toe, Camber and When You Need It
What toe, camber and caster mean on an electric car, the warning signs I look for, how often EVs in the UAE need alignment and what a proper job involves.
· 6 min read

Wheel alignment is the adjustment of the angles at which your wheels meet the road, mainly toe (pointing in or out, seen from above) and camber (tilted in or out, seen from the front). If those angles drift, the tyres scrub sideways as they roll and wear unevenly. On an electric car that scrubbing happens under more weight, so a bad alignment eats tyres noticeably faster.
Most of the EVs I put on our alignment rig are not dramatically out. They are a little out, enough to take 5,000 or 10,000 km off a set of tyres that cost from AED 420 each fitted. That is why I think of alignment as cheap insurance for the tyres, not a repair.
The three angles, in plain terms
| Angle | What it is | What goes wrong when it is off |
|---|---|---|
| Toe | Whether the fronts of the wheels point towards each other (toe-in) or away (toe-out) | Feathered wear across the tread, fast edge wear, slight drag |
| Camber | Whether the top of the wheel tilts in (negative) or out (positive) | Wear concentrated on one shoulder, usually the inner edge |
| Caster | The angle of the steering axis, seen from the side | Steering feels light or heavy, weak self-centring, pull to one side |
Toe matters most for tyre wear
Toe is the angle that destroys tyres fastest. Even 0.2° of extra toe on each front wheel means the tyre is being dragged sideways a few metres every kilometre. Over 20,000 km that is a lot of rubber. Toe is also the angle that changes most easily, from hitting a kerb or a pothole.
Camber is often designed in
Many EVs run noticeable negative camber from the factory, especially at the rear. That improves cornering grip but loads the inner shoulder. Combined with a little toe-out, it produces the inner-edge wear we see on so many Tesla Model Ys. I wrote a full post on that pattern in Tesla Model Y uneven tyre wear.
Caster is rarely the problem
Caster is usually fixed by the suspension design and only changes if something is bent. If caster is out on a car that has not had an accident, I start looking for a damaged arm.
Why alignment matters more on an EV
Three things make EVs less forgiving than petrol cars of the same size.
- Weight. EVs are typically 300–600 kg heavier. The tyre contact patch is pressed harder into the road, so any sideways scrub removes more rubber.
- Instant torque. The motor delivers full torque from standstill. If the wheels are not pointing exactly straight, every hard launch scrubs the tread.
- Expensive, soft tyres. EV tyres use low rolling resistance compounds and often contain acoustic foam. They are not cheap to replace, and some compounds wear faster than a hard touring tyre.
Put those together and the tyres can wear 20–30% faster than on a comparable petrol car before alignment even enters the picture. Add a toe error and that gap grows. Our post on why EV tyres wear faster covers the rest of the reasons.
Signs your EV needs an alignment
These are the clues I ask customers about when they book.
- The steering wheel is off-centre when driving straight on a flat road like Al Khail Road.
- The car pulls or drifts to one side with your hands light on the wheel. UAE roads have a slight camber for drainage, so test on a few lanes before deciding.
- The inner edge of a tyre is worn much more than the outer. Check by running a hand across the tread or looking at the tread wear bars.
- The tread feels feathered, smooth one way and sharp the other, when you stroke across it.
- You recently hit something hard: a kerb while parking, a deep pothole, a speed hump taken at speed.
- You just fitted new tyres. New tyres deserve a fresh starting point.
Vibration is not on that list. A shake at 100–120 km/h is almost always balance or a bent rim, and we fix it with wheel balancing, not alignment.
What happens during an EV alignment in our workshop
A proper alignment is more than putting the car on a machine and printing a sheet. This is how we do it on an EV.
- Lift on the correct points. We use pads at the manufacturer’s jacking points so the battery pack is never loaded. On Teslas we set Jack Mode first if the car has air suspension.
- Check tyre pressures and set them to the placard, cold. Pressure changes ride height slightly and affects the readings.
- Inspect suspension parts for play: tie rod ends, lower arm bushes, top mounts. Adjusting a car with a worn joint is wasted money.
- Mount the targets and take the “before” readings on all four wheels.
- Adjust the rear first, then the front. On Tesla Model 3 and Model Y, rear toe and camber are adjustable, so the rear sets the thrust line for the whole car.
- Centre the steering wheel and set front toe.
- Road test on a straight stretch and recheck if anything feels off.
- Print the before and after so you can see what changed.
Ride height on air suspension
Cars like the Lucid Air, Model S, Model X and Porsche Taycan can sit at different heights. Alignment has to be done at the standard driving height, not the lowered “entry” setting or a raised setting. If the car is aligned at the wrong height, the angles change as soon as it settles.
Driver-assist cameras
Some EVs have a steering angle sensor or front camera that expects the car to drive straight. After a significant alignment change, a few models need a steering angle reset or calibration drive. Teslas usually recalibrate on their own after some driving. If a warning appears after alignment, it is worth checking with the dealer for that model.
How often to do it in the UAE
My rule of thumb is simple: check alignment once a year or every 10,000 to 15,000 km, whichever comes first, and always with new tyres. Heavy users, such as ride-hailing drivers doing 4,000 km a month, should check every six months.
It also helps to combine it with other jobs. When we rotate tyres every 8,000 to 10,000 km, we look at the wear pattern, and that tells us if alignment is drifting before the tyres are ruined. See our rotation schedule for EVs for how the two jobs work together.
Real readings from customer cars
To give a sense of scale, here are typical “before” readings I have seen.
- Model Y Long Range, 38,000 km, Dubai Marina: front total toe about 0.4° out after the owner clipped a kerb in a parking garage. Inner edges of both fronts down to 2 mm while the centre had 5 mm. Tyres replaced, alignment set, steering centred.
- Hyundai Ioniq 5, Mussafah: rear camber within spec, front toe slightly out, steering wheel 3° off centre. A 40-minute job.
- MG4, Sharjah: within spec on all four wheels. The owner was worried about a pull that turned out to be one tyre 7 psi low.
The last one is common. Before paying for alignment, check pressures. A low tyre can make a car pull just like a toe error.
Prices
Wheel alignment starts from AED 150 per car. Cars with adjustable rear axles, air suspension or seized adjusters can take longer. If we find a worn suspension part, we tell you before doing anything else, because aligning on a worn joint will not last.
What I would do
If you have just bought new tyres, have the alignment checked the same day. If your car is a year old and has never been checked, book a check with your next rotation. If one tyre has an inner edge that is noticeably more worn than the rest, do not wait for the next service: that tyre is losing life every week, and catching it early can save the other three.


